Машина зависла,прямо как комп, и ничего не помогает
Добавлено: Вт авг 04, 2009 9:57 am
Привет!
Машина happy HCS 1201-30 s\n: CS04927-L21207
Вот отчет как мы завесили машину
1. загружен дизайн 6.dst
(возможно был еще один поворот в самом начале на 235°, но точно уже не
помню)
2. задал нить и повернул примерно на 225°
3. проверил куда попадает вышивка (смещал немного по Х и У примерно до 5 см)
4. изменил угол поворота установив 215°
5. проверил куда попадает вышивка (смещал немного по Х и У примерно до 5 см)
в этот момент на экране уже были артефакты в виде нескольких горизонтальных
и вертикальных цветных полосок
6. изменил угол поворота установив 220°
7. после перехода в экран вышивки машина встала и не отвечает ни на какие
клавиши.
Вот здесь видео как ведет себя машина при включении
http://nitka29.ru/happy/
При попытке войти в сервисное меню должен показатся экран на котором
показывается ход вышивки - и в нем происходит зависание. соответственно
прошить с кард-ридера невозможно.
например просто при включении машины (до нажатия кнопки "set") срабатывает
обрезка нити (если нажать на кнопку)
при попытки достучатся до машины через УСБ - машину видит, но пишет машина
занята.
до инициализации и после, когда зависает.
не знаю, есть ли возможность прошить через КОМно есть подозрение что нет ((
Подозрения: скорее всего глюк ПО модуля отрисовки - произошел сбой в
вычислении координат, что и вызвало зависание )
ЗЫ. Ждем ответа с нетерпением... буду в Москве примерно 09/08 но к сожалению
проездом.. и повторно вроде 14/08
но буквально недолго, и не в очень удобное время...
Машина happy HCS 1201-30 s\n: CS04927-L21207
Вот отчет как мы завесили машину
1. загружен дизайн 6.dst
(возможно был еще один поворот в самом начале на 235°, но точно уже не
помню)
2. задал нить и повернул примерно на 225°
3. проверил куда попадает вышивка (смещал немного по Х и У примерно до 5 см)
4. изменил угол поворота установив 215°
5. проверил куда попадает вышивка (смещал немного по Х и У примерно до 5 см)
в этот момент на экране уже были артефакты в виде нескольких горизонтальных
и вертикальных цветных полосок
6. изменил угол поворота установив 220°
7. после перехода в экран вышивки машина встала и не отвечает ни на какие
клавиши.
Вот здесь видео как ведет себя машина при включении
http://nitka29.ru/happy/
При попытке войти в сервисное меню должен показатся экран на котором
показывается ход вышивки - и в нем происходит зависание. соответственно
прошить с кард-ридера невозможно.
например просто при включении машины (до нажатия кнопки "set") срабатывает
обрезка нити (если нажать на кнопку)
при попытки достучатся до машины через УСБ - машину видит, но пишет машина
занята.
до инициализации и после, когда зависает.
не знаю, есть ли возможность прошить через КОМно есть подозрение что нет ((
Подозрения: скорее всего глюк ПО модуля отрисовки - произошел сбой в
вычислении координат, что и вызвало зависание )
ЗЫ. Ждем ответа с нетерпением... буду в Москве примерно 09/08 но к сожалению
проездом.. и повторно вроде 14/08
но буквально недолго, и не в очень удобное время...